{"product_id":"matek-f411-one-flight-controller-w-spi-receiver","title":"Matek F411-ONE Flight Controller w\/ SPI Receiver","description":"\u003cp\u003eThis all-in-one FC by Matek is loaded with an STM32411 MCU, built-in SPI receiver(Frsky_X), PDB, BetaFlight OSD, BEC, \u003cem\u003eand\u003c\/em\u003e a current sensor. So pretty much everything but an ESC!\u003c\/p\u003e\r\n\u003cp\u003eTo learn in detail about this new SPI receiver protocol visit \u003ca href=\"https:\/\/oscarliang.com\/spi-rx-receiver-protocol\/\"\u003eOscar Liang's page\u003c\/a\u003e or this brief information taken from Matek.\u003c\/p\u003e\r\n\u003ch2\u003eWhat is SPI RX?\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eRF module 2500-2431 connected to STM32F411 MCU which communicate via SPI\u003c\/li\u003e\r\n\u003cli\u003eRF module 2500-2431 bind with Frsky Transmitter only ( D16 of EU LBT firmware is not compatible now).\u003c\/li\u003e\r\n\u003cli\u003eSPI RX is supported in BetaFlight firmware 3.3\u003c\/li\u003e\r\n\u003cli\u003eSPI RX doesn’t occupy any UARTs\u003c\/li\u003e\r\n\u003cli\u003eTelemetry data \u0026amp; RSSI are sent by default with Frsky_X protocol. No need to enable TELEMETRY in configurator and set up an AUX channel for sending the RSSI data from the transmitter.\u003c\/li\u003e\r\n\u003cli\u003eTelemetry \u0026amp; RSSI work with D16\/D8 of NonEU firmware, and D8 of EU firmware\u003c\/li\u003e\r\n\u003cli\u003eLua script is supported, work with D16 of NonEU firmware\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003cstrong\u003eHow to bind\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e1. Power FC via USB or LiPo normally, RX LED(Green) blinking slowly\u003c\/li\u003e\r\n\u003cli\u003e2. Connect FC to the configurator, Choose “SPI RX support” \u0026amp; “Frsky_X” in Configuration Tab–Receiver mode (They are set by default after flashing)\u003c\/li\u003e\r\n\u003cli\u003e3. Then\u003c\/li\u003e\r\n\u003cli\u003eCLI “frsky_bind” and press ENTER, the RX LED will come solid.\u003c\/li\u003e\r\n\u003cli\u003eor Press RX Bind button, RX LED will come solid also\u003c\/li\u003e\r\n\u003cli\u003e4. Start Transmitter in bind mode, the RX LED will fash slowly – Bind complete.\u003c\/li\u003e\r\n\u003cli\u003eFrsky_X — Transmitter D16(CH1-8 9ms or CH1-16 18ms)\u003c\/li\u003e\r\n\u003cli\u003eFrsky_D — Transmitter D8(CH1-8)\u003c\/li\u003e\r\n\u003cli\u003e5. After CLI “defaults” or reflashing, SPI RX should be bound again.\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\r\n\u003cp\u003eFlight Controller\u003c\/p\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eTarget: MATEKF411RX\u003c\/li\u003e\r\n\u003cli\u003eMCU: 100MHz STM32F411CEU6\u003c\/li\u003e\r\n\u003cli\u003eIMU: MPU6000 gyro\/accelerometer (SPI)\u003c\/li\u003e\r\n\u003cli\u003eOSD: BetaFlight OSD w\/ AT7456E chip\u003c\/li\u003e\r\n\u003cli\u003eSPI RX: module 2500-2431, Frsky_X or Frsky_D protocol\u003c\/li\u003e\r\n\u003cli\u003eVCP, UART1, UART2\u003c\/li\u003e\r\n\u003cli\u003eWS2812 Led Strip: Yes\u003c\/li\u003e\r\n\u003cli\u003eBeeper: Yes\u003c\/li\u003e\r\n\u003cli\u003ePPM: RX2 pad\u003c\/li\u003e\r\n\u003cli\u003eBlackbox: No\u003c\/li\u003e\r\n\u003cli\u003eSBUS input: No\u003c\/li\u003e\r\n\u003cli\u003eI2C1 SDA \u0026amp; SCL: No\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003ePDB\u003c\/p\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eInput: 6~30V (3~6S LiPo) w\/TVS protection\u003c\/li\u003e\r\n\u003cli\u003ePDB: 4x30A (Max.4x46A)\u003c\/li\u003e\r\n\u003cli\u003eBEC: 5V 2A cont. (Max.3A)\u003c\/li\u003e\r\n\u003cli\u003eLDO 3.3V: Max.300mA\u003c\/li\u003e\r\n\u003cli\u003eCurrent Sensor 184A (Scale 179)\u003c\/li\u003e\r\n\u003cli\u003eBattery Voltage Sensor: 1:10 (Scale 110)\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e3x LEDs for FC STATUS (Blue) , RX (Green) and 3.3V indicator(Red)\u003c\/li\u003e\r\n\u003cli\u003e4x PWM \/ DShot outputs\u003c\/li\u003e\r\n\u003cli\u003e2x UARTs\u003c\/li\u003e\r\n\u003cli\u003e1x Group of G\/S1\/S2\/S3\/S4 pads for 4in1 ESC Signal\/GND\u003c\/li\u003e\r\n\u003cli\u003e4x pairs of corner pads for ESC Power connections\u003c\/li\u003e\r\n\u003cli\u003e1x Side-press button for BOOT(DFU) mode\u003c\/li\u003e\r\n\u003cli\u003e1x Side-press button for RX bind\u003c\/li\u003e\r\n\u003cli\u003e36x46mm PCB with 30.5mm mounting holes\u003c\/li\u003e\r\n\u003cli\u003e10g\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003cimg src=\"http:\/\/cdn.getfpv.com\/media\/wysiwyg\/product-detail-images\/F411-ONE_C_1.jpg\"\u003e\u003c\/p\u003e\r\n\u003ch2\u003eIncludes\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e1x Matek 411-ONE Flight Controller\u003c\/li\u003e\r\n\u003cli\u003e1x Rubycon ZLH 35V\/470uF (Low ESR)\u003c\/li\u003e\r\n\u003cli\u003e6x silicon grommets M4 to M3\u003c\/li\u003e\r\n\u003cli\u003e2x IPEX- 2.4G antenna 15cm\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cp\u003e\u003c\/p\u003e","brand":"Matek Systems","offers":[{"title":"Default Title","offer_id":15481557844031,"sku":"8561","price":52.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0084\/8301\/2671\/products\/matek-f411-one-big008_1.jpg?v=1570083204","url":"https:\/\/dronecosmo.myshopify.com\/products\/matek-f411-one-flight-controller-w-spi-receiver","provider":"DroneCosmo","version":"1.0","type":"link"}