{"product_id":"lumenier-lux-v2-flight-controller","title":"Lumenier LUX V2 Flight Controller","description":"\u003cp\u003eThe Lumenier LUX V2 flight controller is the next generation of the popular Lumenier LUX. It uses a powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz \u003cstrong\u003e(high speed SPI) \u003c\/strong\u003eusing popular Betaflight, CleanFlight and RaceFlight firmware along with ultra low looptimes. The LUX comes with BetaFlight pre-installed.\u003c\/p\u003e\r\n\u003cp\u003eThe LUX V2 builds on all the best features of the V1 board and further improves on hardware components and layout. Now you get a whopping 5x dedicated UART ports for periphials, along with an SD Card slot for practically unlimited data logging. The MPU has also been updated to the low noise MPU6000 Gyro making tuning even easier. No longer do you need to solder jumper pads for PPM\/SBUS selection, it is automatically chosen via software! The powerful F3 MCU also supports the latest DSHOT protocol available in the newest BetaFlight firmware.\u003c\/p\u003e\r\n\u003cp\u003eThe Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. Signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS, DSMX). A signal inverter is already included for S.BUS. \u003cem\u003ePlease note: PWM input for individual channels is not supported. \u003c\/em\u003e\u003c\/p\u003e\r\n\u003cdiv id=\"product-notice\"\u003e\n\u003cstrong\u003ePlease Note:\u003c\/strong\u003e The LUX V2 has its own target in Betaflight, be sure not to update it with the old LUX V1 firmware.\u003c\/div\u003e\r\n\u003ch2\u003eHardware Features\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e\u003cstrong\u003eNew in V2\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e\u003cstrong\u003eDedicated UART for RC RX use, no need to solder a jumper to select PPM\/SRX anymore.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eDedicated telemetry UART, this brings the total to 5x plus USB.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cli\u003e\n\u003cstrong\u003eSD Card slot for BlackBox data recording \u003c\/strong\u003e\u003cem\u003e(SD card not included)\u003c\/em\u003e\n\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eLow noise MPU6000 SPI Gyro.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eUSB detection can disable things like buzzer when configuring on the bench.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eNew ultra low noise regulators for MCU and IMU power systems.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003cli\u003e\n\u003cstrong\u003eUSB Conflict resolution \u003c\/strong\u003e- Hardware inversion, SBUS or telemetry can be used on any of the \u003cstrong\u003e3\u003c\/strong\u003e available hardware serial ports. USB will not interfere with peripherals.\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eHigh Speed SPI 8kHz Gyro \u003c\/strong\u003e\u003c\/li\u003e\r\n\u003cli\u003eMPU interrupt connected to F3, allowing the F3 to know immediately when fresh data is available.\u003c\/li\u003e\r\n\u003cli\u003eDedicated Boot button for easy firmware flashing.\u003c\/li\u003e\r\n\u003cli\u003eReinforced solder pads for trouble-free direct soldering.\u003c\/li\u003e\r\n\u003cli\u003eExtremely low profile design.\u003c\/li\u003e\r\n\u003cli\u003eRecessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.\u003c\/li\u003e\r\n\u003cli\u003eIntegrated FRSky RSSI Filter (RC filter).\u003c\/li\u003e\r\n\u003cli\u003eInput voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).\u003c\/li\u003e\r\n\u003cli\u003eVIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry\/OSD voltage data.\u003c\/li\u003e\r\n\u003cli\u003eFiltered voltage output - output 5v 1A (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v\/3.3v RX selectable.\u003c\/li\u003e\r\n\u003cli\u003e\u003cstrong\u003eNote: RX pad is dedicated to UART 4 in the Configurator.\u003c\/strong\u003e\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eSoftware\/Hardware Features\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eBetaflight support (\u003cstrong\u003eSupports new DSHOT protocol\u003c\/strong\u003e)\u003c\/li\u003e\r\n\u003cli\u003eCleanflight support (RACE target).\u003c\/li\u003e\r\n\u003cli\u003eBLHeli passthrough flashing supported by hardware \u003c\/li\u003e\r\n\u003cli\u003eRaceflight ready\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003eSTM32F303\u003cstrong\u003eRCT6(256kB flash)\u003c\/strong\u003e 32-bit processor\u003c\/li\u003e\r\n\u003cli\u003eMPU6000 SPI Gyro\/Accelerometer\u003c\/li\u003e\r\n\u003cli\u003eMicro SD memory card slot \u003cem\u003e(SD card not included)\u003c\/em\u003e\n\u003c\/li\u003e\r\n\u003cli\u003eHigh quality, gold plated PCB\u003c\/li\u003e\r\n\u003cli\u003eHighest quality components, individually sourced to meet Lumenier standards\u003c\/li\u003e\r\n\u003cli\u003eMicro USB connector for programming\u003c\/li\u003e\r\n\u003cli\u003e\n\u003cstrong\u003eDimensions:\u003c\/strong\u003e 36x36x6mm (includes USB in height)\u003c\/li\u003e\r\n\u003cli\u003e\n\u003cstrong\u003eMounting Holes:\u003c\/strong\u003e 30.5mm square to center of holes \u003c\/li\u003e\r\n\u003cli\u003e\n\u003cstrong\u003eWeight: \u003c\/strong\u003e5g\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eIncludes\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e1x Lumenier Lux V2 Flight Controller\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eDownloads\u003c\/h2\u003e\r\n\u003cul\u003e\r\n\u003cli\u003e\u003ca href=\"http:\/\/www.getfpv.com\/media\/wysiwyg\/product-user-manuals\/Lux-V2-Quick-Start-Guide.pdf\" target=\"_blank\"\u003eDownload the Lumenier LUX V2 Quick Start Guide\u003c\/a\u003e\u003c\/li\u003e\r\n\u003cli\u003e\n\u003ca href=\"https:\/\/chrome.google.com\/webstore\/detail\/cleanflight-configurator\/enacoimjcgeinfnnnpajinjgmkahmfgb\" target=\"_blank\"\u003eDownload Cleanflight\u003c\/a\u003e (Target coming soon)\u003c\/li\u003e\r\n\u003cli\u003e\n\u003ca href=\"https:\/\/chrome.google.com\/webstore\/detail\/betaflight-configurator\/kdaghagfopacdngbohiknlhcocjccjao?hl=en\" target=\"_blank\"\u003eDownload Betaflight Configurator\u003c\/a\u003e - \u003ca href=\"https:\/\/github.com\/betaflight\/betaflight\/releases\" target=\"_blank\"\u003eLatest Betaflight Firmware\u003c\/a\u003e  (Load the \"\u003cstrong\u003eLUXV2_Race\u003c\/strong\u003e\" target)\u003c\/li\u003e\r\n\u003cli\u003e\n\u003ca href=\"https:\/\/chrome.google.com\/webstore\/detail\/raceflight-configurator\/ffkgelfmnmeofidahjaefimpdgekflha\" target=\"_blank\"\u003eDownload Raceflight\u003c\/a\u003e (Target coming soon)\u003c\/li\u003e\r\n\u003c\/ul\u003e\r\n\u003ch2\u003eVideos\u003c\/h2\u003e\r\n\u003cp\u003e\u003cstrong\u003eJoshua Bardwell Review\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003ciframe height=\"365\" src=\"https:\/\/www.youtube.com\/embed\/m4ygG6Y5zXI?rel=0\" style=\"border: 0;\" width=\"633\"\u003e\u003c\/iframe\u003e\u003c\/p\u003e\r\n\u003cp\u003e\u003cbr\u003e\u003cspan style=\"font-size: x-small;\"\u003e\u003cem\u003eLumenier™ and LUX™ are registered trademarks\u003cstrong\u003e \u003c\/strong\u003e of Lumenier.\u003c\/em\u003e\u003c\/span\u003e\u003c\/p\u003e","brand":"Lumenier","offers":[{"title":"Default Title","offer_id":14939477966911,"sku":"6597","price":21.26,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0084\/8301\/2671\/products\/lumenier-lux-v2-flight-controller.jpg?v=1570046323","url":"https:\/\/dronecosmo.myshopify.com\/products\/lumenier-lux-v2-flight-controller","provider":"DroneCosmo","version":"1.0","type":"link"}